Trailed and attached equipment for cascade walk-behind tractors. Attachments: increasing the efficiency of the Cascade walk-behind tractor

Motoblocks of domestic production trademark“Cascade” have earned a good reputation and for at least ten years have been one of the most popular among villagers and summer residents. This recognition did not come naturally. Walk-behind tractors "Cascade" are produced in accordance with technical requirements And international standards ISO-9002 quality.

They are equipped with a steering wheel that is adjustable in height and horizontally, which allows you to adjust it to your height, as well as turn it to the side so as not to trample the cultivated ground. The low center of gravity allows you to save effort when working. More on other features of the Cascade walk-behind tractor below.

Motoblocks "Cascade" are produced in the city of Perm. Their manufacturer is OJSC "Reductor-PM" (PM - Perm Motors), part of the enterprise "Aviation Gearboxes and Transmissions - PM".

This plant, part of the Russian Military-Industrial Complex, dates back to 1951, and specializes in the production and after-sales service of gearboxes and transmissions for domestically produced helicopters.

Pavilion of JSC "Reductor-PM" at the international exhibition of the helicopter industry "HeliRussia".

Walk-behind tractors appeared on the company’s product list in 1995 and became one of the few concrete manifestations of the then fashionable term “conversion” (i.e. transition military industry for the production of purely civilian products).

The main function of the Cascade walk-behind tractor is pre-sowing tillage. Complete with appropriate mounted implements, the walk-behind tractor is designed for surface plowing, loosening and soil cultivation; leveling areas intended for sowing. In the future, “Cascade” will be useful for hilling crop plants and inter-row cultivation.

In addition, "Cascade" walk-behind tractors successfully work with the widest range of additional attachments - various cutters, hillers, walk-behind shovels, diggers, and trolley trailers. Attachments are attached to the walk-behind tractor using special “metal fingers”, which ensure good reliability and sufficient rigidity of the hitch.

The list of drive equipment available for use with Cascades includes: rotary snow blowers, water pumps, hay mowers, mechanical potato planters, feed crushers. In these cases, the supply of useful force is carried out from power plant. The drive equipment is installed in front of the walk-behind tractor and operates via an additional belt drive.

The Cascade walk-behind tractor consists of four main elements: engine, transmission, chassis and controls. The chassis also includes the metal tubular frame of the walk-behind tractor with the wheels attached to it. Important Feature“Cascade” is the ability to change its track, that is, the inter-wheel space, during operation.

The wheels on these walk-behind tractors are used both rubber pneumatic and rubber cast, as well as weighted metal ones. You can use the Cascade walk-behind tractor without wheels - with cultivator cutters. The cultivator for "Cascade" - "KMB 1.002.000" - has a diameter of 350 mm and provides rotary cultivation of the soil to a depth of 20 cm, with a working width of 45 cm (when installing two cutters) and up to 93 cm (when installing four cutters).

The function of transmitting torque from the engine to the wheels is performed by the walk-behind tractor transmission. It consists of a clutch, gearbox and chain reducer. These individual transmission elements are installed on Cascade walk-behind tractors, both individually and in a single unit. Other operational functions of the walk-behind tractor transmission are assistance in adjusting the speed of work and ensuring its turns while moving along the work area.

Any of the engines internal combustion on walk-behind tractors "Cascade" - gasoline, carburetor, single-cylinder, four-stroke, with air cooled. Ignition is electronic non-contact. Spark plug - type “A11-1 OST 37.003.081-98”.

The engine is started using a manual starter with a pull cord. The noise level at the walk-behind tractor operator's workplace is, according to the manufacturer, 89 dBA. The vibration level on the controls (local vibration) does not exceed 135 dBA.

Over the years of production at this technique tried installing similar ones technical specifications, both domestic engines, produced in-house by the Perm plant, and Chinese “Briggs & Stratton”, “Honda”. (Yes, Briggs & Stratton is an American company, and Honda is a Japanese company, but engines for walk-behind tractors of these brands are made in China). Gradually the motors Russian production are a thing of the past, and the “Cascades” of the last years of production are all equipped with Chinese “engines”.

The domestically produced “DM-66” and “DM-68” engines are sleeved single-cylinder OHV engines with overhead valves. Built-in automatic decompressor ensures low starting effort. The working volume of the DM-66 and DM-68 engines is 317 cubic centimeters. These engines run on any gasoline - AI-80, AI-92, AI-95.

The oil sump volume of the DM-66 and DM-68 engines is 1.4 liters. The orientation of the crankshaft is horizontal. The cylinder diameter is 76 millimeters. The maximum torque is 14.2 N.m. Overall dimensions – 45x41x43 cm. Weight – 28 kg. Average fuel consumption is within two liters per hour.

Briggs&Stratton engines of the INTEK I/C and Vanguard OHV series, also single-cylinder, of a similar design to the DM, have a displacement of 208 cubic centimeters and a rated power of 4.8 kW (6.5 hp). The cylinder diameter is 68 mm. Maximum torque – 12.6 N.m. Overall dimensions – 32x38x35 cm.

It is characteristic that the power indicators, according to the company’s official website, were established “according to Briggs & Stratton estimates.”

Many, not unreasonably, consider the best of the Cascade walk-behind tractors to be those equipped with a Honda engine. And in fact, the Honda GC-200 engine is perhaps the most common “engine” in the world of walk-behind tractors – both domestic and Asian-made; It has been produced for decades and has an almost impeccable reputation.

The Honda GC-200 motor has a really high operating efficiency and slow wear of parts. It also features lower fuel consumption - not 2, but 1.7 or even 1.5 liters of gasoline per hour on average. The working volume of the Honda engine is 196 cubic centimeters; maximum power – 6.5 horsepower (at 3600 rpm). Cylinder diameter – 68 mm; maximum torque – 12.4 N.m. Overall dimensions – 32x38x35 cm.

IN recent years The market is dominated by the version of the Cascade walk-behind tractor, equipped with a cheaper analogue of the Honda GC-200 engine - also a Chinese-made Lifan engine, model Lifan 168F-2.

The clutch of the "Cascade" walk-behind tractors is belt-type. The clutch mechanism operates on the basis of belt tension of a V-belt type transmission. Gearbox (two types are used, factory indices “005.45.7700” and “005.45.7530” on this walk-behind tractor - chain type, two-speed

The manufacturer notes that the gearbox on the Cascade walk-behind tractor is reinforced, its output shaft is mounted on large-diameter bearings. This ensures high resistance of the mechanisms to vibrations and shocks.

Chain reducer of the "Cascade" walk-behind tractor.

As standard, “Cascade” walk-behind tractors are equipped with pneumatic tires 4.00-10, model TU 38.304-13-13-92; or cast, massive, with channels on the sides, 5.00L-12, model F-232 TU 38.304-13-05-92.

• cutters that allow you to cultivate the land on a strip with a width of 45 to 93 centimeters. If the land does not belong to the category of virgin or particularly hard soils, then it makes sense to add two additional cutters to the two standard cutters, more than doubling the strip of land being simultaneously cultivated.
• hiller. Very convenient and useful equipment, the value of which will be appreciated by anyone who has tried it in action. It not only destroys weeds in the inter-row space, but also adds soil to the stems and roots of cultivated plants, helping them develop and grow.
• flat cutter It not only loosens the soil, but also crushes the roots of weeds, reducing labor costs for further weeding of the area.
• trailer-trolley. Of course, the walking speed of the walk-behind tractor is very low, but, in any case, it is better to transport bags of potatoes or other heavy or dirty cargo in a cart, rather than dragging them “on your hump.” The same - construction waste, various tools and materials. The trailer is designed for a load of up to 600 kilograms.

• feed crusher Eliminates the need to take grain to the mill to grind it into crushed grain. It is convenient and reasonable to prepare crushed porridge for pigs and other livestock right in your barnyard.
• mower. Anyone who has tried to mow with a regular scythe and prepare hay for the winter to feed even just one cow and calf knows what a long and difficult work it is. The mower reduces labor costs and time for making hay several times.
• water pump. If there is a river or other body of water near the garden, then why not stretch a hose there and install a pump. Especially if the water supply is in summer period interruptions happen. The Cascade walk-behind tractor will provide such a strong and stable water pressure that watering the garden will take very little time. You just need to stock up on a special sprinkler attachment for the hose so that it doesn’t wash away the soil along with the cultivated plants.
• snow blower. Clearing snowdrifts after heavy snowfall with a shovel is pleasant only for the first 10-15 minutes of this work. With the help of a walk-behind tractor, the process will go disproportionately faster and more efficiently.
• potato planter and digger. Villagers will confirm that while planting potatoes with an ordinary shovel is not the most labor-intensive task, then digging them up is already hard and persistent work. More than half of the labor costs, subject to the use of appropriate equipment, will be transferred to the “metal shoulders” of the walk-behind tractor.

Over the years of production, Reductor-PM OJSC has brought to the market so many modifications of the Cascade walk-behind tractor that, at first glance, it seems that there are too many of them and you can get confused in them. However, this is not true. In fact, it's simple. You just need to “read” the alphabetic and digital designations in the factory indices of these walk-behind tractors.

MB6 – model with domestic engine(“DM66” or “DM68”). MB61 – model with engine foreign production(“Briggs & Stratton” or “Honda”).

01 – steering rod. 02 – rotating steering column, which allows you to adjust the position of the steering wheel in the vertical and horizontal planes.

In the 04 series gearbox, the gearbox output shaft is mounted on needle bearings. In gearboxes of the 05, 06, 07 series, the gearbox output shaft is mounted on ball bearings.

Also, the gearboxes of the 05 and 06 series provide a reduced speed in first gear, which provides a number of advantages, for example, when working with a mower and snow blower, it allows you to mow grass and remove snow more efficiently.

The gearboxes of the 06, 07 series also use a mechanism for decoupling the output shafts, which makes it easier to control the walk-behind tractor when turning, and increases its maneuverability when used as a vehicle and during soil cultivation.

Basic options on the basis of which all modifications of the Cascade walk-behind tractors are made:

• Walk-behind tractor "Cascade MB 6-84"– with engine "DM-66" 6 horsepower, and standard transmission. Gas tank volume: 4.5 liters. Weight: 103 kg.
• Walk-behind tractor "Cascade MB 6-82"– with engine "DM-68", 6 horsepower, and a reinforced transmission. Gas tank volume: 3.3 liters. Weight: 103 kg.
• Walk-behind tractor "Cascade MB 61-122"– with engine Briggs & StrattonINTEKI/C", 6.5 horsepower, and a reinforced transmission. Gas tank volume: 3.6 liters. Weight: 94.5 kg.
• Walk-behind tractor "Cascade MB61-22/01"– with engine "Honda GX200", 6.5 horsepower, and a reinforced gearbox. Gas tank volume: 3.6 liters. Weight: 94.5 kg.
• Walk-behind tractor "Cascade MB61-104"– with engine Briggs&Stratton VanguardOHV» , 6.5 horsepower, and a standard transmission. Gas tank volume: 4.5 liters. Weight: 96.5 kg.

Each modification of the Cascade walk-behind tractor provides a standard tillage depth of up to 26 centimeters. The processing width while the walk-behind tractor is moving is 45, 60 or 95 centimeters.

Overall dimensions and weight indicators:

• Length – 1500 mm (+/-30 mm); Width – 590 mm (+/-30 mm); Height – 1150 mm (+/- 50 mm). - In working position.
• Length – 970 mm (+/-30 mm); Width – 450 mm (+/-30 mm); Height – 935 mm (+/- 50 mm). – In transport position.
• Track width: without extensions – 350 mm; with extensions – 610 mm.
• Ground clearance – 140 mm.
• The smallest turning radius of the walk-behind tractor is 1.1 m.
• Steering wheel rotation angle: in the horizontal plane to the right/left – 180°/45°; in the vertical plane up/down – 170°/100°.
• Number of fixed steering positions: in the horizontal plane – 24; in the vertical plane – 36.
• Motoblock weight, maximum – 103 kg (with wheels); 85 kg (with cultivators).

Estimated speed of movement of the walk-behind tractor, at a crankshaft speed of 300 rpm:

• Forward, in first gear – 3.04…4.29 km/h;
• Forward, in second gear – 10.30…11.09 km/h;
• Backward – 3.04…4.29 km/h.

Digging up the soil of even a small plot is backbreaking work not only for an elderly person, but can also be a blow to the health of young people. It was developed to make it easier to care for the area. special equipment, namely walk-behind tractors.

Attachments for the Cascade walk-behind tractor allow you to perform any work - from plowing the land to cleaning your garden plot from dirt, debris and leaves.

Types of attachments and their purpose

Cascade walk-behind tractors are reliable, compact and easy to operate. You can choose the right model for yourself, which will be designed specifically for the size of your plot.

To make the Cascade walk-behind tractor work for you all year round, experts recommend purchasing various attachments.

You will be able to clean the area, transport goods, plant and harvest potatoes, and, of course, cultivate the land.

At the rear of the walk-behind tractor there is an output shaft, and it is attached to it attachments. It should be noted that it is best to purchase original fastening parts and attachments. This way you will be confident in the reliability and durability of the product, as well as in the fact that it will hold firmly on the machine itself due to the high-quality coupling.

So, attachments for the Cascade walk-behind tractor come in the following types:

You can also purchase an adapter. This is a design with which you can easily upgrade your walk-behind tractor to a mini tractor. As you know, this is already a professional equipment and its price on the market is not affordable for everyone. But any craftsman can make a mini tractor with his own hands.

The Cascade walk-behind tractor is an agricultural unit designed to perform technological operations on household plots and land plots. The equipment was developed and produced by the largest Russian company OJSC Reduktor-PM, specializing in the manufacture of helicopter gearboxes and transmissions.

Motoblocks are simple, easy to use, compact, have small overall dimensions and weight. Agricultural machinery is in great demand among domestic users due to its excellent technical performance.

The product is available in 2 types depending on the motor:

• model with a foreign engine Briggs&Stratton (USA), Robin-Subaru, Honda (Japan) - MB-61;
• model with a Russian engine - MB-6 (DM-66, DM-68).

Walk-behind tractors are conventionally designated as follows: after the MB-6 or MB-61 block, the series numbers of the engine, gearbox, and controls are indicated. For example, a model that belongs to the class heavy walk-behind tractors, MB61-22-02-01 is equipped with a Japanese overhead valve gasoline Honda engine The GX200 OHV is air-cooled, with 02 series heavy-duty gear reduction with ball bearings on the output shaft and 01 series steering. This unit is capable of handling large areas and any agricultural work.

Specifications

The technical characteristics of the Cascade MB-6 walk-behind tractor are as follows:

1. Engine type: 1-cylinder, 4-stroke carburetor, air-cooled.
2. Power - 6 hp
3. Working volume - 317.4 cm³.
4. Cylinder diameter - 76 mm.
5. The volume of oil in the engine is 0.9 l.
6. Crankshaft rotation speed - 2750-3250 1 rpm.
7. The type of running system is wheeled in a 2x2 pattern.
8. The clutch is a V-belt drive.
9. Belt size for walk-behind tractor Cascade:
   • forward belt - A-1180 internal IV GOST 1284.1-89;
   • reverse belt - A-1400 IV GOST 1284.1-89.
10. Gearbox - 2-speed.
11. Gearbox seals:
    • 941/20 GOST 4060-78 - 7 pcs.;
    • 942/30 GOST 4060-78 - 2 pcs.;
    • 306K GOST 8338-75 - 2 pcs.;
    • 942/15 GOST 4060-78.
12. Number of gears:
    • forward travel - 2;
    • reverse gear - 2.
13. The working width with the KMB 1.002.000 cultivator is 930 mm.
14. Processing depth - 100-200 mm.
15. Operating temperature - -5...+35°С.
16. Overall dimensions - 1500x600x1150 mm.
17. Machine weight - 103 kg.

The Cascade MB-61 walk-behind tractor has the following design features:

The features of the Cascade MB61 distinguish it from the agricultural equipment Cascade MB6. Motorized vehicles are efficient, reliable and well-built, but the cost of units with American and Japanese engines is much more expensive. Therefore, walk-behind tractors with domestic engines are more popular among farmers.

Fuel consumption

For walk-behind tractors MB-6 Cascade with Russian engines DM-1 fuel consumption is no more than 2 l/hour. Tank volume - 4.5 l.

The Briggs&Stratton engine has a 3.6 liter fuel tank. Fuel consumption is 1.6-1.8 l/hour.

The reliability and long service life of the walk-behind tractor depend on the operating conditions, maintenance, care of the unit, and proper running-in after its purchase. To do this, you must follow all recommendations for operating the equipment.

They boil down to the following:

1. Assemble the walk-behind tractor. The assembly diagram can be found in the instructions that came with the unit upon purchase.
2. Fill the tank with clean gasoline.
3. Check the oil level in the engine crankcase.
4. Inspect the wheel mountings.
5. Check engine valve clearances. The valves are adjusted using feeler gauges of 0.10-0.25 mm.
6. Run-in as follows:
   • do not start work with a cold engine;
   • the engine must first idle;
   • do not load the engine during operation;
   • running-in should last at least 30 hours;
   • work only in first gear;
   • After break-in, change the engine oil and check the bolt connections.
7. Adjust the tension of the forward and reverse belts of the V-belt drive by changing the length of the chains.
8. Check the operation of the controls.
9. Lubricate the starter regularly.
10. Fill the gearbox with oil in a timely manner.
11. Do not allow it to get into the filters.

Many farmers are wondering what kind of oil should be poured into the walk-behind tractor. In particular, they are interested in the MB 6841 walk-behind tractor with M-12GI or M-10GI filling. These are old brands of oils and are not so easy to find.

The following fuels and lubricants are suitable for Cascade walk-behind tractors:

• in the fuel tank - motor gasoline Normal-80, GOST R 51105-97;
• in the engine crankcase - motor oil M-5z/10G1, M-6z/10V, M-6z/12G1, GOST 10541-78;
• for the gearbox - transmission oil in accordance with GOST 23652-79 or aviation oil MS-20, GOST 21743-76.

Synthetic and mineral materials cannot be mixed.

Carburetor settings

Initial carburetor adjustment is made at the factory. The user must not perform any repair work during the warranty period. If starting is poor, inspect the spark plug. If the spark plug is damp, then the problem is in the ignition system. If the spark plug is dry, check that fuel is entering the carburetor.

Repair of the carburetor on the Cascade walk-behind tractor is carried out only in specialized workshops.

Troubleshooting

The manufacturer guarantees uninterrupted operation of the equipment for up to 5 years, provided that all care and maintenance recommendations are carefully followed. The warranty period is 24 months. During this time, there should be no attempts to independently repair the equipment by breaking the seals.

The units may have the following malfunctions:

1. The Cascade walk-behind tractor does not start, the engine does not start.
2. The ignition system does not work. Adjusting the ignition of a walk-behind tractor is based on inspecting the spark plugs, as described above.
3. Unstable operation of the motor or stopping after starting.
4. It is difficult to start the engine, black exhaust gases come out.
5. The walk-behind tractor does not move forward or backward.
6. Delamination of the V-belt drive belt.
7. The engine does not develop power.

These are typical failures and malfunctions in the operation of the walk-behind tractor.

Reasons

If the engine does not start, the reasons may be the following:

• lack of fuel in the tank;
• the gas tap is closed;
• clogging of the fuel system;
• clogging of the hole in the tank plug;
• fuel leaks from the carburetor;
• The ignition system does not work;
• air intake into the carburetor through the flanges.

If the engine is unstable, the reason is low fuel consumption; if starting is difficult and there are exhaust gases, on the contrary, high fuel consumption, clogging air filter, excess oil in the crankcase.

If the walk-behind tractor does not have forward or reverse gear, the belt may break or have insufficient tension.

If the engine does not operate at the stated power, then the problem is a weakened spring or carbon deposits in the combustion chamber.

Walk-behind tractor repair

Repair work is carried out in accordance with the repair instructions for the Cascade walk-behind tractor.

It is recommended to carry out servicing at a repair shop. Specialists will adjust the carburetor, if there is no forward or reverse gear, they will check the gearbox, repair the gearbox, and replace worn parts.

In case of minor malfunctions of the walk-behind tractor, the owner can eliminate the cause himself.

If there are problems with the fuel system, the following actions must be taken:

1. Fill with fuel.
2. Check if the hole in the plug is clogged. To do this, you need to remove the plug in the tank and clean the hole.
3. Drain the fuel from the tank, rinse it with gasoline, and blow out the carburetor jets with a pump.

Malfunctions in the ignition system are resolved using the following methods:

1. Replace the spark plug.
2. Check and replace the spark plug tip.
3. If the permissible dimensions of the gap between the stator and the magnetic shoe of the flywheel change, adjust it.

If the air filter is clogged, clean the filter element.

If the causes of failures are in the V-belt drive, check the belt tension, adjust them or replace them.

After repairing the Cascade walk-behind tractor, the unit should work efficiently and for a long time.

Do-it-yourself hitch to a walk-behind tractor

It is an important component that reliably connects the unit with additional equipment. It has a U-shape and is often used in connection technology. It is produced in factories, and some farmers make it themselves.

To do this, take a channel of suitable size and drill holes. Through the holes on one side it is attached to the walk-behind tractor; on the other, the support of the linkage mechanism is fixed to the channel body.

Attachments

To carry out work on the equipment it is not required special knowledge. Professional skills are required when installing additional devices to equipment.

Complete with attached and trailed equipment, the walk-behind tractor can perform the following operations:

• loosening the soil;
• plowing the site;
• crushing and incorporation of weeds into the soil;
• cultivation;
• uniform mixing of fertilizers with soil;
• weeding between rows;
• hilling of industrial crops;
• mowing grass and small shrubs;
• clearing the area of ​​snow;
• transportation of small cargo.

• weedweed;
• hiller;
• plow for walk-behind tractor;
• mower;
• lugs;
• potato digger;
• snow removal attachment.

With the help of these mechanisms, the walk-behind tractor can perform a wide range of technological processes at the sites.

Cascade MB-6 is a multi-purpose walk-behind tractor, one of the leaders in sales on the Russian market. The machine has a number of advantages in which it is practically not inferior to more expensive analogues. This model is in high demand largely due to its good driving characteristics and reliability. Trust in the Cascade MB-6 walk-behind tractor, as well as in all products of this brand, is confirmed positive reviews real motorists. The machine is widely in demand among Russian summer residents, and also finds its application in the municipal and economic spheres. Demand for the MB-6 model is also observed among farmers and gardeners. Let's consider the main advantages of the technology, pay attention to the rules for first use, and also highlight the main technical parameters walk-behind tractor.

The MB-6 cascade is produced by the Reduktor company. The model was designed in 2006, and for such short time managed to gain the trust of Russian business executives. In terms of its capabilities, this walk-behind tractor can compete with more high-end machines, as it is equipped with a powerful motor and additional functions, making work efficient and convenient, regardless of the complexity of the tasks. The ability to install various attachments significantly expands the potential of the MB-6 Cascade, and thereby makes it even more versatile.

The performance of the walk-behind tractor is designed to process an area of ​​up to 40 acres.

Design features of the equipment:

• Robust chain gear and dry clutch
• 4-speed manual transmission maintains optimal speed
• Steering column with adjustable height and horizontal position. All controls for the walk-behind tractor are located on the handle. They are located as conveniently and ergonomically as possible
• Chassis lock function if necessary
• Large pneumatic wheels – for increased geometric maneuverability

First use rules

The Cascade MB-6 walk-behind tractor needs to be run in immediately after purchasing the product. This procedure is necessary to ensure that internal parts are worn in and adapted to local weather and road conditions. Thanks to this, the car will last much longer. At the same time, the frequency of unpredictable breakdowns will be significantly reduced, and maintenance will need to be carried out only in accordance with the regulations. So, for proper break-in, it is important to follow the following steps:

• Before starting the procedure, you should remember that running-in does not involve operating the walk-behind tractor at maximum load. Only partial load is allowed - it is believed that this mode is the most favorable for running in parts
• First of all, we start the engine and let it run for 40-50 minutes at idle speed. IN at the moment It is also necessary to carry out maintenance of the gearbox - engage each gear one by one, and repeat this for at least 5-10 minutes
• During the running-in, it is allowed various types works, including hilling, cultivation, plowing, transporting goods, pumping water and other household tasks. It is important that during the break-in period the load on the walk-behind tractor does not exceed half of the maximum permissible value. For example, when transporting goods, it is allowed to transport up to 250-300 kg while the permitted 500-550 kg
• The run-in can be considered completed after 8-10 hours. We drive the equipment into the garage and begin maintenance. First of all, you need to pay attention to the condition of the external panels, as well as the lower part of the walk-behind tractor and consumables. If necessary, you can add fuel, change filters, wheels, etc.
• The next day, the walk-behind tractor can be subjected to maximum load.

Attachments

The manufacturer did not provide a single attachment option in the basic configuration of the walk-behind tractor, which can be considered an advantage rather than a disadvantage. Indeed, in this case, the buyer has the opportunity to choose the right set himself, and at the same time save on unnecessary options. Let's highlight the most popular options for the Plowman MB-6:

• Potato digger, potato planter - necessary for planting and digging all types of crops
• Hiller – provides gentle care for agricultural crops
• A plow is a means for the initial processing of the earthen surface. The reinforced transmission together with the plow allows you to cope with even the most difficult virgin soil
• Blade shovel - snow removal module rigidly attached to the walk-behind tractor
• Hay mower - used for making hay, and also useful for working in the area around the house
• Water pump - a means of pumping water from reservoirs for watering crops
• Trolley, trailer - a means of transporting goods weighing up to 500 kg
• Mower is a device for cutting grass, mowing lawns, etc.

As you can see, the Cascade MB-6 walk-behind tractor is adapted for use in any climatic zones. This is facilitated by a large range of attachments, making the equipment more versatile and suitable for wide range tasks.

Specifications and engine

Dimensions: length – 830 mm, width – 480 mm, width – 740 mm. Device weight – 103 kg.

Engine – DM66, four-stroke single-cylinder, volume 0.3 liters. Power – 6 horsepower. There is support for AI-92 and AI-95 gasoline. The gearbox is chain type, with needle bearings. Tank capacity – 4.5 liters. Transmission – four-speed, with two forward and two reverse speeds

Fuel consumption

The Cascade MB-6 walk-behind tractor consumes an average of 1-1.5 liters per hour. Fuel consumption may increase slightly, for example when transporting heavy loads, when driving uphill, or when using soil hooks and cultivating the soil to great depths.

Prices in Russia

The average cost of a Cascade MB-6 walk-behind tractor on the domestic market is 35 thousand rubles. Not included in base price additional equipment. A set of mounted options can be purchased separately for 10-12 thousand rubles, depending on the set of options.

Competitors: Neva MB-2B-6.0, Favorit MB Honda GX160 5.5, Caiman Vario 60S TWK+, Ugra NMB-1N12, Cascade MB61-25-02-01, Pubert Vario 55B TWK+.

The "Cascade" walk-behind tractors are similar in the way they attach attachments to many Russian, Belarusian and Chinese walk-behind tractors. For this reason, both proprietary and third-party attachments can be used for them. Next - more detailed description attachments for walk-behind tractors "Cascade".

Okuchniki

Examples of hiller models: Strela-3, Lepestok, Strela-2. Some products have a reinforced design, so they last longer.

The plow is one of the most popular mounted implements for walk-behind tractor. You can install a plow of any model on the Cascade, but it is better to give preference to simple designs.

Plow Mole Plow reversible Plow PN-1-20MB

Possible models of plows for Cascade walk-behind tractors: reinforced universal plow, universal plow PNM-1-20, plow with skimmer, reversible, with support wheel and others.

Tracked modules

A module or attachment with tracks allows you to make a heavier and more powerful structure out of a walk-behind tractor.

The attachment for the “Cascade” is also suitable for the “Neva” or “Oka” walk-behind tractor.

Hitches

The hitch is necessary for connecting attachments to the walk-behind tractor. Average weight hitch is 5 kg. Product dimensions: length 43 cm, width 13 cm. Using the hitch, you can attach a hiller, plow, harrow and other devices to the “Cascade” walk-behind tractor.

Double universal reinforced hitch

Milling cutters for the Cascade walk-behind tractor can be conventional, collapsible, bolt-mounted, equipped with stoppers, crow's feet, without shafts or with shafts. Milling cutter sets usually include knives, bushings, connecting shafts, stoppers, bolts, nuts, and lock washers.

Also, depending on the power of the walk-behind tractor, it is possible to install a solid cutter, for example, a Fighter (length 140 cm), or a branded Centaur soil cutter with 6 knives with a protective housing.

Potato planter

The potato planter for the Cascade walk-behind tractor has the following parameters:

• track width 40-50 cm,
• planting depth can be adjusted from 10 to 15 cm,
• The permissible size of tubers is up to 6 cm in diameter.
• The width of the “Cascade” potato planter is 45 cm.
• length - 70 cm (excluding handles),
• height - 60 cm.

The weight of such a device is 22 kg. Several more models of potato planters: KP-1 Expert, KS-12, KSC-1, K-1L and others.

Potato digger

Recommended models of potato diggers for walk-behind tractors "Cascade": KM-3, KMT-3, KMT-1, A5. You can use a conveyor digger with a Premium active knife. The potato digger used for Centaur models, which weigh more than 100 kg, is suitable.

It is allowed to use digging machines from Zirka, Intertul, Volodar, KM-2, K-30 and others. Take into account the weight of the unit and the dimensions of the digger; attachments that are too heavy are not suitable for small-weight walk-behind tractors.

Snow removal equipment

Winter operation of the Cascade walk-behind tractor involves the purchase of attachments for snow removal. Such equipment includes snow blowers, for example, auger blowers, from any manufacturer.

Snow blower Neva

Models of snow blowers suitable for walk-behind tractors "Cascade": WM1050, GN (width 50 cm), GRUNFELD ST360, AL-KO SnowLine 560. It is acceptable to use snow removal modules from manufacturers Korund, Neva, Skiff, Patriot, Volodar and others.

Blade

The blade shovel used for clearing snow together with the Cascade walk-behind tractor can be regular or reinforced, with or without a rubber pad along the bottom edge.

Standard blade width for walk-behind tractors: 1 m. Blade shovels are produced by such manufacturers as TM Yarilo, Zirka, Korund, Volodar, Buff, Brigadier and others.

Mowers

Many models of mowers are suitable for the Cascade walk-behind tractor, for example: SHIP rotary mower, Motor Sich rotary mower, Forte belt mower, Centaur KR-02, K-1 from Zubr, Zirka, Patriot and others.

For more delicate work than simple grass mowing, the manufacturer recommends using segment mowers.

Rotary mower Zarya Rotary mower Patriot KKR-4

Adapters

The adapter is a riding structure attached to the walk-behind tractor. It is equipped with a seat for the operator of the machine. Models of adapters suitable for use with the Cascade: motor-tractor adapter from TM Yarilo, But, AU-1, BUM-3, universal adapter for walk-behind tractors Zirka, Neva, Patriot, Motor Sich AD-2V.

Front walk-behind adapter

Speed ​​reducers

The creeper is designed to increase the traction force of the unit by increasing the torque. For the Cascade walk-behind tractor, as for other units, the speed reducer is selected based on the power of the unit itself.

Creeper "ZIRKA-135"

That is, to a 6 hp walk-behind tractor. you need a device marked “for cars with a power of 6 hp.” For the Cascade walk-behind tractor, you can use creepers Zirka - 105-135 (width 50 cm, length 24 cm, weight 17 kg), Pubert, Solo, Husqvarna, Viking, Robix, TM Yarilo and others.