Automatic water supply system water jet prof. Borehole pumps Gilex water jet house

Description:Automated water supply system Gilex Vodomet 60/72 HOUSE. The Vodomet centrifugal submersible pump is a multi-stage electric pump with “floating” impellers, a “washed” electric motor and a built-in capacitor. The Vodomet submersible pump is designed to supply water from wells with an internal diameter of 100 mm or more, as well as wells, reservoirs and open reservoirs for the water supply system of the house, garden irrigation.

Peculiarities:

Submersible pumps "VODOMET" compared with vibration pumps:

• have greater efficiency, since rotational motion is more economical than reciprocating motion due to the absence of a “start-stop” mode;
• submersible pumps are less noisy;
• submersible pumps are much more durable, since they do not have a quickly worn out valve-piston system;
• submersible pumps do not have a harmful effect on the well and the entire water supply system, since they do not have significant vibration. Silence is one of the the most important features"Vodojet" pump: the house will not be filled with extraneous noise during its operation.

Well pumps"WATER-JET" compared to vortex jets:

• borehole pumps have greater efficiency;
• are not subject to changes in parameters over time, while in vortex pumps, wear of the working surfaces reduces the flow-pressure characteristic;
• well pumps are less noisy;
• borehole pumps are not so sensitive to contamination.

Pump "VODOMET" with "floating" impellers compared to traditional ones:

• has greater hydraulic efficiency due to the independent setting of “zero” gaps, which increases the pressure characteristics of each impeller. This reduces their required quantity, i.e. the axial dimensions of the pump, the mass of the rotating parts, and, consequently, vibrations are reduced;
• has less tendency to clog, as it is able to pass large particles. The Vodomet system is ideal for use in domestic conditions: the house will always have a working water supply system.

VODOMET pumps with a “washed” electric motor have a number of advantages compared to devices of a traditional design:

• the location of the electric motor above the pumping part allows the power cable to be removed from the top cover of the pump, which reduces its dimensions and allows the pump to be mounted in a well with a casing pipe of a smaller diameter (it is cheaper);
• the electric motor of the well pump is reliably protected from overheating by the flow of water washing it, which passes through the annular gap between the stator shell and the pump housing;
• the location of the seal at the top point of the hydraulic part of the pump protects it from sand, and, therefore, significantly increases its service life;
• the pump layout allows it to be used in a partially submerged position, for example, in open shallow reservoirs.
• VODOMET submersible pumps with a built-in capacitor eliminate the capacitor box and allow the use of a regular three-core cable instead of a four-core one, which simplifies installation.
• the use of a mesh (1.5x1.5 mm) filter instead of a slot filter more effectively prevents the penetration of long particles into the pump that can clog the pump. All parts of the pump that come into contact with the pumped water are made of materials approved for contact with food.

The main components of the automated water supply system "VODOMET DOM": submersible pump of the "VODOMET" series, control panel with pressure sensor, 50 l hydraulic accumulator. made of carbon steel, filter housing 10", check valve, ball valve, pressure gauge, fittings.

Manufacturer

Manufacturer: GILEKS is a well-known manufacturer of pumps and pumping equipment. The JILEX company was founded on January 5, 1993 in the city of Klimovsk, Moscow region. It was a young, rapidly developing enterprise. Today, JILEX LLC is already widely known as a leading manufacturer of pumps of the highest quality. Also, we can say with confidence that the products produced by the pump manufacturer "GILEX" are intended specifically for the Russian market. It should be noted that branded pumps from the manufacturer "GILEX" are characterized by wear resistance, ease of maintenance, the ability to operate normally in the most difficult conditions and at the same time have a more attractive price compared to foreign analogues. In addition to constantly improving the design and expanding the range, such important points for consumers and professionals as design, dimensions, ease of installation and availability of repairs are taken into account.

Every day, specialists at the GILEX pumping plant improve pump designs, thereby expanding and making the model range more efficient. The main goal The company's desire is to make pumps sold from the manufacturer "GILEX" available to as many consumers as possible.

Specifications

Specifications:

Maximum flow, l/min
Maximum head, m
Power consumption, W
Cable length, m
Max. size of passed particles, mm
Maximum immersion depth, m

It is an automated water supply system with a submersible centrifugal multistage pump, “floating” impellers, a “washed” electric motor, a built-in condenser and a set necessary equipment. All components are made of durable and wear-resistant materials in accordance with hygienic certificates and are adapted for use in Russian conditions.

Description
The Vodomet Prof 55/75 DOM system is an automated water supply system with a submersible centrifugal multistage pump, “floating” impellers, a “washed” electric motor, a built-in condenser and a set of necessary equipment. All components are made of durable and wear-resistant materials in accordance with hygienic certificates and are adapted for use in Russian conditions.

Equipment
The delivery package for an automated water supply system includes various components that perform specific functions in the system:

• submersible pump Vodomet Prof 55/75 - water supply from wells, wells, reservoirs and open reservoirs
• control panel with pressure sensor - ability to program the pump operating mode
• hydraulic accumulator (50 l) - accumulation of water under pressure, “smoothing” water hammer
• filter housing - placement of a standard 10" cartridge
• three-terminal fitting (1") - connecting the hydraulic accumulator to the water supply line
• ball valve (1") - shutting off, if necessary, the water supply line
• pressure gauge - pressure determination
• check valve(1") - preventing water from flowing out of the water supply system back into the well
• fitting (1"-1") - connecting the check valve to the discharge line

Design
A downhole electric pump consists of a pump part and a “washed” electric motor, which are located in a single housing made of stainless steel. Asynchronous motor sealed and protected from overheating by a thermal protector built into the stator winding.
“Floating” impellers are run-in and can move in the axial direction.
To secure the cable, there are two eyes located in the rear cover of the pump with the outlet pipe. There is also a waterproof cable coming out of the back cover, simplifying the procedure for connecting the pump.

Distinctive features

• complete set for water supply
• high hydraulic efficiency
• no vibration
• low noise level
• motor protection
• dry running protection
• simplified installation
• long service life
• modern design

Advantages
The well pump of this model is modified for use in “sand-filled” wells, therefore it is capable of pumping water with a high content (up to 300 g/m3) of sand in suspension.

Compared to vibration and vortex pumps, Vodomet is more productive due to its economical rotational movement and is less noisy. Due to the absence of significant vibration, the pump does not have a harmful effect on either an individual well or the entire water supply system as a whole.

“Floating” impellers have increased pressure characteristics and are less prone to clogging. Independent setting of “zero” gaps leads to greater hydraulic efficiency.

The flow of water passing between the stator shell and the pump housing reliably protects the “washed” electric motor from overheating.

Installation
The borehole pump is completely ready for operation; you just need to plug the plug into the socket. However, all electrical installation work (installation of a socket, connection to the power supply, grounding, etc.) must be carried out by a specialist in accordance with safety regulations.

Installation of the device in a well involves placing the pump in a casing pipe with a minimum internal diameter of 100 mm. In order to protect the well from ingress groundwater etc. It is better to cover the top of the pipe with a cap.

To immerse the pump into the well, use a steel cable pulled through two eyes in the top cover of the pump. The presence of a built-in capacitor allows the use of a regular three-core cable (instead of a four-core one), making installation much easier.

It is prohibited to install the pump at the bottom of the well to avoid stopping the pump. The distance to the bottom of the well must be at least 1 meter.

Application
System Vodomet Prof 55/75 HOUSE used for supplying water from wells with a diameter of 100 mm and above, wells, reservoirs and open reservoirs. Ideal for automated water supply at home, garden irrigation.

Note
It is strictly prohibited to pump flammable and chemically active liquids, as well as water containing abrasive and solid substances.

Recommendations
The pump should be protected from direct exposure sun rays and do not place it near heating devices.
Before a long period of inactivity, the pump must be rinsed in clean water, the remaining water must be drained, and then the device must be dried.
The ambient temperature in the room where the pump is installed should not drop to minus values.

Quality assurance
The Vodomet DOM series system has high performance, unpretentiousness to the purity of the pumped water and resistance to voltage fluctuations in the electrical network, which confirms its high-quality and reliable operation throughout its long service life.

Operating restrictions

• maximum permissible sand content - 300 g/m 3
• maximum number of pump starts - 20 times per hour
• the maximum depth of pump immersion under the water surface is up to 30 meters, but not less than 1 meter from the bottom of the source
• maximum particle size - 1.5 mm
• permissible temperature range of pumped water - from +1°C to +35°C

Pump flow and pressure characteristics

Vodomet system DOM 55/75- in addition to the submersible centrifugal pump, it includes all components for an automatic water supply device. It is mainly used for uninterrupted water supply to a home or cottage. The source of water can be a well or a well with a sufficient flow rate.

All components and parts of the system are carefully selected based on numerous tests and technological calculations, as well as design features each node. This allowed us to achieve excellent stability and performance.
The programmable control panel allows flexible control of the water supply system and also carries a number of protective functions.
The use of this system, which includes a Vodomet pump, allows you to achieve increased productivity and long-term pump service, as well as serious energy savings due to smooth switching on and off of the electric motor and optimization of pump operating time.

Peculiarities:
- presence of a programmable control panel with a pressure sensor
- the kit includes a water pre-purification filter
- has high reliability and durability: the hydraulic accumulator and submersible centrifugal pump are made of wear-resistant and chemically inert materials, which allows the use of this pump for drinking water supply.

Specifications

Maximum flow rate, l/min - 55
Maximum head, m - 75
Power consumption, W - 880
Voltage, V/Hz - 220/50
Current consumption, A - 4
The number of stages in the pump is 9.
Maximum diving depth, m -30
Diameter of solid impurities, no more than, mm - 1.5
Pump cable length, m - 30

The Vodomet DOM system includes:

15. Submersible centrifugal pump Vodomet 55/75
16. Plastic filter housing
17. Hydraulic accumulator.
18. Programmable control panel with operation indication and pressure sensor.
19. Check valve
20. Ball valve
21. Triple fitting 1 inch and connecting fittings.
22. Pressure gauge.

Remote Control

The basis of this remote control is a microprocessor controller. There is a keyboard and an intuitive display with sensors.
What information does the display show:
- pressure in the water supply system
- current consumption, A
- mains voltage
- load factor of the electric motor.
Controller functions:
- maintaining the programmed pressure range in the system with an accuracy of 0.1 atm.
- smooth start and stopping the pump - this reduces starting currents, prevents water hammer, and reduces the mechanical load on all pump elements.
- protection against voltage surges (in the range of 160-250V) and current overloads during operation
- protection against dry running by monitoring a sharp drop in pressure and reducing the current consumption.
Important! All these factors together lead to safer and longer pump operation.

The package includes

Pump complete with cable - 1 pc.
Control panel with pressure sensor - 1 pc.
Hydraulic accumulator - 1 pc.
Fitting - 1 piece.
Check valve - 1 piece.
Operating instructions - 1 piece.
Warranty card - 1 piece.
Container - 1 piece.

Design and operational features of the DOM Vodomet

Good design and high quality The Vodomet pump, which is the pumping part of the water supply system, allows for efficient water supply with maximum efficiency.
- the presence of a programmable control panel (with a pressure sensor) with which the system is controlled.
- presence of a hydraulic accumulator
- presence of a water pre-filter
- a check valve included in the system prevents water from flowing out of the pipes back into the well or borehole.

Thanks to the presence of a programmable control panel and carefully selected components that form a single whole, this system can be used both for water supply at home or cottage, and for small businesses - small industrial production, farms, greenhouses with drip irrigation, etc.

Before installing the system, for further uninterrupted operation, you should calculate water consumption and take into account the following factors:
- static and dynamic well level
- well flow rate
- possible maximum volume of water consumption per day and per unit of time.
- the depth of the well or well, as well as the elevation difference on the site.

Thanks to the electronic components of the control panel, the system will operate automatically, but we recommend periodically monitoring the data displayed on the electronic display and indicator lights for possible optimization of the operation of the submersible pump and the entire system as a whole.

Contact our specialists for advice if you need more detailed information for selection of pumping equipment.

How to buy the DOM Water Jet System

You can buy the Vodomet DOM pumping system by placing an order directly on the online store website, or by calling the phone in the Contacts section. Our manager will contact you and arrange delivery or reserve the goods for pickup.

If you need the DOM Vodomet System in Moscow, delivery throughout the city and the nearest Moscow region is at your service. For buyers from other regions of Russia - any delivery transport company or postal service by agreement.

Payment for goods is carried out in the following ways:

1.Payment in cash.

When picking up from the store, or when receiving the goods to the courier.

2.Bank transfer - payment according to the invoice issued for payment as for legal, and for physical persons

When placing an order, select the payment method: "Bank transfer".

After confirming the order, our specialist will contact you and after agreeing on all organizational issues, you will be sent an invoice e-mail which you can pay in any bank or via an Internet client.

1.Pickup.

Pickup times and times:

PVZ m. Sokol: you can pick up your order the next day after ordering from 10 to 18 weekdays. The order is stored at the point of issue for 3 working days.

Pickup cost:free when ordering over RUB 1,000. (for orders less than 1,000 rubles, the cost of pickup is 80 rubles.)

Attention! Only pre-reserved items are available at the order pick-up point!

The employee at the delivery point does not give any advice on goods!

Directions to the pick-up point are located on the page

2. Delivery in Moscow within the Moscow Ring Road

The following items are delivered free of charge:

Kerosene heaters trademark"Sengoku"

Cost of delivery:

If your order weighs more than 20 kg, the manager will calculate and inform you of the additional delivery cost!

Delivery time:

Delivery is carried out on weekdays from 10:00 to 20:00.

Behind 30-90 minutes the courier calls you and agrees on the exact time of arrival.

Exact delivery address (city, street, house number, apartment or office number, intercom code)

The contact person

Contact phone numbers

3. Delivery beyond the Moscow Ring Road and further within the Moscow region

Cost of delivery:

If the product card does not indicate WEIGHT, you can check it with the manager.

If your order weighs more than 20 kg, the manager will calculate and inform you of the additional delivery cost!

Delivery time:

Delivery is carried out within 1-3 working days from 10:00 to 20:00 without reference to half a day.

Behind 1-2 hours before delivery, the courier calls you and agrees on the exact time of arrival.

What is important to indicate when ordering:

Exact delivery address ( city, region, locality, street, house number, apartment or office number, intercom code)

The contact person

Contact phone numbers

4. Delivery to regions of the Russian Federation

We can send you goods from any of the companies listed below.

SDEK - www.cdek.ru

First Expedition Company (PEC) - www.pecom.ru

The estimated cost of delivery of goods can be found on the websites of these companies or contact our specialist.

What is important to indicate when ordering:

Passport series and number, date of issue

Full Name

Receipt city

If none of the above methods suits you, we will send the goods to your address in another way - as agreed with you.

That is why this article is devoted to a review of the most promising domestic and foreign pumping stations, with the help of which it is possible to build a productive and trouble-free autonomous water supply system.

And in our opinion, the “three” most successful devices are as follows.

From the name of this system it is clear that “Vodomet-Dom” is aimed specifically at the domestic sphere. Moreover, four models of the Vodomet-Dom system allow you to cover literally the entire niche: from small buildings (country houses) served by the 60/32 model to low-rise dwellings (cottages and townhouses) equipped with the 60/92 model.

And please note: the performance of the Vodomet-Dom system is stable in both cases. After all, both the younger and older models pump about 60 liters of water per minute (determined by the first two-digit figure in the model name).

Well, the difference between these models is the pressure, which is 32 and 92 meters (determined by the last two-digit figure in the model name). That is, we have a high-performance system with the ability to adjust the height of the water column.

Of course, such attractive characteristics did not arise out of nowhere. Vodomet-Dom has a very attractive design, since the pumping unit of this autonomous water supply system can be both submersible and surface (main).

And in the first case, “Vodomet-Dom” pumps water even from 100-mm wells, filled not even with liquid, but with a suspension containing 1-2 kilograms of sand per 1000 liters of water. In the second case, the pump is integrated into the main line itself, using a special fitting, which allows you to assemble a surface pumping station that operates even in severe frosts. However, such a pump can pump only relatively clean water, with a sand content of no more than 300 grams per 1000 liters.

Another advantage of the Vodomet-Dom system is a gigantic 50 liter hydraulic accumulator, which can satisfy current needs sufficiently big family or several families living in an apartment cottage.

The standard delivery package for the Vodomet-Dom system includes the following components:

• Hydraulic accumulator 50 liters.
• Submersible pump "Vodomet" or main pump "Vodomet M".
• Filter unit with wear-resistant housing.
• A set of shut-off and control valves, which includes such components as a three-terminal fitting, a ball valve and a check valve.
• A control unit with protection against voltage surges (the station operates only in the range from 160 to 250 Volts) and a control and measuring unit (pressure gauge).

The cost of the “Vodomet-Dom” kit ranges from 17 to 24 thousand rubles. Manufacturer: Gilex company (Russia).

The Vodomet Chastotnik station was created to please consumers with “above average” demands. After all, this unit works with twice the productivity of the model from the “Vodojet Dom” series.

Moreover, four models of the Vodomet Chastotnik series are aimed at both domestic and commercial needs. After all, the “youngest” model – 115/75-CH – pumps up to 115 liters of water per minute from a 30-meter well, supplying it with a pressure of 75 meters. And this is quite enough to supply water to multi-apartment low-rise buildings (townhouses).

The older model - 125/125-CH - gets water from the same deep well, but with a productivity of 125 liters per minute it provides a pressure of 125 meters. And such characteristics can be used even in public utilities or in handicraft production.

Moreover, all stations from the Vodomet Chastotnik series are equipped with special submersible pumps"Vodomet-Ch", controlled automatically using a unit built in by the manufacturer. And such a unit ensures a smooth supply of liquid with the required pressure, regardless of water consumption. In addition, the Vodomet-Ch units have a built-in dry-running protection unit and a soft start unit, which increases the duration of the trouble-free period of operation.

The capacity of the hydraulic accumulator of the Vodomet Chastotnik pumping station is 50 or 100 liters. Moreover, a more capacious storage device is installed on older models equipped with pumps with a power of more than 1.5 kW. A 50-liter tank is installed on younger models, which are equipped with pumps with a power of about one kilowatt.

In addition to the tank and pump, the Vodomet Chastotnik station kit includes the following components:

• A control unit with its own pressure relay (RDM-5), equipped with a voltage stabilizer that equalizes the current characteristics. Therefore, the station operates without failures even in conditions that are far from ideal - at voltages from 160 to 250 Volts.
• A set of shut-off valves, which includes a ball valve and a check valve (it prevents water from draining into the well)
• A set of control and control valves, which includes a three-terminal fitting (flow distributor mounted on the neck of the hydraulic accumulator) and a pressure gauge.

The cost of a station from the “Chastotnik Vodomet” series ranges from 27 to 40 thousand rubles. Manufacturer: Gilex company (Russia).

Grundfos is a very reputable Danish company that produces high-quality pumping equipment. Moreover, according to the company, it relates to every second unit sold on the global compressor equipment market.

Well, in the downhole equipment segment, Grundfos has strengthened its position thanks to the well-known SQE series of household stations. Moreover, SQE deep water pumps from Grundfos are famous for both their quality and performance. After all, even the “younger” models from this series are capable of “reaching” up to 9000 liters of liquid per hour from a considerable depth, lifting it with a 50-meter pressure.

However, the SQE series from Grundfos also has some disadvantages that do not allow these units to be put in first place in our rating. And such disadvantages include, firstly, the high price - the average cost of the SQE kit from Grundfos is 50,000 rubles, and, secondly, the small volume of the hydraulic accumulator, equal to 8-10 liters. In addition, repairing such an expensive station cannot be cheap. And given the remoteness of the “spare parts” manufacturer, it will not be accessible.

But Grundfos guarantees that the service life of stations from the SQE series will exceed 10 years. And the automatic control unit for the water supply system will provide not only protection against dry running, but also a smooth start-up of the “aggregate” part of the station.

The scope of supply for the Grundfos SQE series is standard. It includes a deep-well pump, a hydraulic accumulator, an automation unit, shut-off and control valves.

The cost of a station from the SQE Grundfos series ranges from 40 to 60 thousand rubles. Manufacturer: Grundfos (Denmark).