How to remove protective glass from your phone. Replacing glass on a smartphone on your own: description, recommendations and requirements How to remove old protective glass from a phone

There are several ways to remove protected glass from your phone screen. The one you need to use will depend on how well the glass is attached to the display. Before you start removing the protective glass from your smartphone screen, you should warm up the screen at a low air temperature for about 15 seconds. It should slightly melt the adhesive on the protective glass. It is important not to overdo it by bringing the hair dryer nozzle too close, as this may damage the screen. After which you can simply use your fingers or some flat thing that will help create a gap between the screen and the protective glass. The last step is to carefully remove the glass.

First, you can try to remove the protective glass with your own fingers, without using improvised means. Perhaps it was secured loosely enough to allow this operation to be performed without effort. You just need to try to catch the edge of the glass with your fingernail. This should be done on the side that is least affected by cracks or chips.

If the protective surface easily succumbed to this influence and moved away from the screen on at least one side, then removal can continue. As soon as it starts to rise, you need to further move under the protective film with your fingers, and not remove it with one jerk. This will help prevent cracks from appearing. This should be done slowly and evenly, otherwise a lot of glass shards may form.

If the protective glass cannot be removed so easily, you can try using a toothpick to pry up one of the corners. As soon as you manage to lift the corner of the glass up, you need to pull it with your fingers, as in the previous method, slowly and evenly. In addition to a toothpick, you can use a credit card, a piece of thin cardboard, or any flat object. You just need to insert an existing item into the gap between the screen and glass, and then slowly push it down to lift the protective glass from the display.

Installing a new protective glass on your smartphone screen

There are two ways to install protective glass on your smartphone screen. They provide for dry and wet glass installation, respectively. The first method is for protection using tempered glass, which does not come with a special solution.

First, you need to clean your phone screen with a lint-free microfiber cloth. Then you need to detach the glass from the sticky side from the factory protective film. After that, you need to carefully attach the protective glass to the screen, making sure that the Home button, speaker and holes for the camera are located exactly in their places. You can use a credit card or any other tools to ensure even coverage and prevent bubbles.

Wet installation is designed to be protected by tempered glass, which comes with a spray bottle (usually containing alcohol) to assist with installation. Some people prefer to use protective films and glass in this way, since this method completely prevents the penetration of dust and small hairs. Then you should repeat all the steps from the previous method.

The glass on a mobile phone is one of the most fragile elements. If a mobile device falls on asphalt or rubble, the screen will break in most cases. And even the use of durable types by manufacturers does not help - the displays still break. In this case, you have to buy a new one and also spend money on replacing the glass on your smartphone. However, you can try to carry out this operation yourself.

Theory

Before you start manipulating the software on your smartphone, you need to know what you have to deal with. The main elements here will be:

Matrix, which is a liquid crystal panel. It is on this that the image you see is formed. In some phones, the matrix is located under protective glass, while in other models these two elements are one. The matrix is connected to the main board of the smartphone through special cables.
Touchscreen. This is a glass panel that breaks when the smartphone is dropped. This is what will have to be changed. If the touchscreen and matrix are one solid element, then if the touchscreen breaks down, the matrix will also have to be replaced. It's expensive.
Frame and buttons.
Backlight.
Loops.

Procedure for replacing glass on a smartphone

When dropped, the touchscreen is always the first to suffer, and then the matrix may also break. In any case, the replacement order will look like this:

Disassembling a smartphone.
Removing the main module from the housing.
Warming up the screen.
Separation of the touchscreen from the main module. Sometimes it is removed along with the matrix.
Cleaning from glue residues and dust.
Applying adhesive to install a new touch glass. Irradiation with a lamp for quick drying.
Housing assembly.

Instructions

If your phone's matrix and touchscreen are different elements, separate from each other, then you can handle this simple procedure yourself. This will help save money, because the price of replacing the glass on a smartphone can cost 1000 rubles, and it only takes 10 minutes.

For work we will need:

Shaped screwdrivers.
Hairdryer Preferably an assembly one.
Scotch tape or glue.
Mediator.
Gloves.
Plastic card.
Spatula.

Some of these accessories come with your new screen.

You need to start with the bolts. Unscrew the bolts using a small shaped screwdriver. Most often, a torx screwdriver is required. Place all the bolts in one place so as not to lose them. A regular matchbox is ideal. Many models have a hidden bolt on the upper left side of the smartphone. It also needs to be unscrewed.

Now we take a pick and with its help we try to remove the smartphone’s case around the perimeter. This tool is ideal for this purpose. Many people try to remove the cover with a screwdriver, but it leaves small dents on the sides, which are immediately visible and even felt when you pick up the phone. Therefore, a pick is an ideal tool for removing a smartphone case.

Pay attention to the side latches. They need to be pressed a little to remove the housing. These latches are fragile and break easily, so be careful when doing so. If you break any of them, the case will not fit as tightly as before.

Now you need to remove the buttons that are on the sides. Take tweezers and carefully remove them without touching any cables. If there is a top on/off button for the smartphone, then it also needs to be removed.

After dismantling the buttons, we move the main board, but we do it very carefully, because under it there is a cable to the touchscreen. You need to disconnect it and connect the cable of the new touch glass. This is necessary to check functionality. After connecting the cable, turn on the smartphone and swipe your finger over the new touchscreen. If it works, then you can begin to completely remove the previous glass.

We remove the old glass and glue the new one

To remove the glass with a hairdryer, you need to warm up the areas where it is attached to the case (usually the touchscreen is attached to the front of the case). Warming up is done at a temperature of 70 degrees for 5-10 minutes. During this time, the mounting adhesive will melt and the touchscreen will easily come off. You can then attach the new sensor to the main part of the phone. At this stage there are 2 options:

Remove any remaining old glue. Glue double-sided tape instead and attach the new sensor to it. Note that this is the correct method, but it is more labor-intensive, because it is necessary to remove the old glue, and this is quite difficult.
Replace the protective glass on your smartphone using old glue. This can also be done, and the adhesion of the new sensor to the glue will be strong. But first you need to warm up the old glue with a hairdryer after you have torn off the old touchscreen.

Did you glue new glass? Now you need to insert the cable from the sensor into the connector where the cable from the old glass was connected. Then you need to reassemble the phone in the reverse order.

How much does it cost to replace glass on a smartphone?

If you go to workshops, you will have to pay for the screen and the work of the master, which, depending on the workshop and region, can be estimated at 500-1000 rubles. By replacing the glass yourself, you can save money. In this case, it is better to order the sensor through a well-known Chinese website, which will save even more.

If you change the display in the cabin on a new smartphone, the replacement will be very expensive and often amounts to 50% of the cost of the phone itself, and sometimes even more. Therefore, if you have the skills to replace displays and sensors, then sometimes it pays to do it all yourself, even if it takes much more time than in a workshop.

In cases where the sensor and matrix of a smartphone are one whole, replacement will also be expensive, because the matrix itself is an expensive element, and the price of the sensor is cheap. Of course, the image on such displays looks high-quality, but if the glass falls and gets damaged, repairs cost a hefty sum.

Conclusion

Replacing the glass on a smartphone with your own hands is a simple task that requires experience, nothing more. If you want to learn how to do this, then practice first on an old smartphone that you don’t mind ruining. After one or two procedures, you will learn and can easily make the replacement yourself. True, different models may have their own subtleties, but you will figure it out.

The main function of protective glass is to protect the phone from shock, cracks and scratches. This element takes care of everything. Over time, it becomes unusable as it loses its attractive appearance. Because of this, the level of protection of the device is reduced. To replace it, you must first learn how to remove the protective glass from your iPhone. This procedure is simple. You just need to follow simple rules.

Why is replacement required?

Before you learn how to remove iPhone 6 and 5, you need to familiarize yourself with the reasons for the replacement:

The appearance of the phone is spoiled.
The protective functions of the device are lost.
If you want to change it to a new glass.

When the phone has a new protective glass, the device looks neat. There are special accessories for the iPhone that are ideal in size. But you can also use universal ones, which need to be glued correctly.

Precautionary rules

You need to take into account one important nuance before removing the protective glass from the iPhone 5 or 6. Since the surface of the screen is perfectly smooth, the glass is securely fixed to it. It is held not only by glue, but also by electrostatic forces. The two surfaces are firmly in contact, and therefore the glass will not be removed so easily. You have to pry it off with your fingernail. If you use another object, such as a knife, for these purposes, there is a possibility of damaging the display.

One won't help here either. If it sticks securely to the damaged surface, there will be no vacuum under it and it will bounce off with force. When the grip is good, the suction cup does not come off, but another difficulty will appear.

The sensor is attached to the body with double-sided tape or glue. Their strength is less compared to the touchscreen and protective glass. If you apply force, you can tear off the entire screen module, which will damage its cables. Therefore, actions must be deliberate. Only then can you use the instructions on how to remove the protective glass from an iPhone 5s or another type of device.

Preparation

The work must be done carefully. Before removing the protective glass from your iPhone, you need to prepare everything for the procedure:

Mediator.
Silicone suction cup.
Lint-free cloth.
Wiper.
Medical gloves.

Some glass kits include everything needed to complete the procedure. If these parts are there, then the work is easy.

Features of dismantling

How to remove the protective glass from an iPhone so that everything turns out neatly. Before the procedure, you must wash your hands with soap and dry. You can use rubber gloves. This is necessary to protect against fingerprints and streaks. The screen will look neat.

On the damaged glass, you need to find a whole corner where there are no chips or other damage. You need to attach it with a suction cup, pressing it to the device. The corner with the suction cup must be pryed off using a mediator or spatula so that the glass peels off. To do this, you need to pull the suction cup in your direction.

The procedure must be performed carefully so that the screen is not torn off before a gap forms. If there is no suction cup, you can smoothly insert the pick into the gap that appears. When peeling, you need to deepen the mediator. With a large screen you need to use two tools. Finally, you need to lift the suction cup towards you to completely remove the glass.

New glass sticker

When the user knows how to remove the protective glass from the iPhone, you can safely carry out the procedure. Then you will probably need to glue a new element. To ensure a high-quality result, work should be done in a clean room. Before gluing, you need to apply a cleaner and treat the surface with it. This is necessary to completely eliminate dust and degrease the surface.

The glass must be grasped by the edges. Hands should be washed and dried. You can work with medical gloves. Then you need to pull the tab of the protective film that is on the adhesive surface and remove it. The glass should be kept close to the smartphone to prevent dust particles from sticking during operation.

The glass is placed away from the sensor; it must be centered and leveled. You need to make sure that all the holes match. The product must be lowered onto the display, pressing it slightly. Bubbles must be eliminated immediately by wiping the surface with a dry cloth. At the end, you need to remove the film, which served as protection for the product during transportation.

It is better to immediately eliminate dust particles that have fallen under the glass. It is necessary to carefully peel off the glass, removing any debris. To do this, you can use a napkin or tweezers. Then the glass is put in place. After this, the phone will again be protected from damage. The procedure for removing and gluing glass is the same for all iPhones. You just need to choose the right accessory.

The protective glass on Apple gadgets is designed to protect the devices from damage. Typically, a high-strength chemical composition is used to protect the display from chips and scratches. Some users neglect such protection, but in vain. Protective glass for iPhone 6 and other gadgets can significantly extend the life of your mobile device.

In this article we will look at how to remove the protective glass from iPhone 5 and devices of other versions. We will also pay attention to how to glue protective glass on an iPhone. In addition, we will try to identify the advantages of this method of protecting the display over conventional film.

How to change and how to glue the glass - read the detailed instructions below.

If we compare the 2 main methods of protecting the iPhone display screen - glass and film - most criteria will be in favor of the first.

The advantages of glass coating are:

Increased strength with a small thickness of only 0.25 mm.
The presence of an oleophobic coating that prevents fingerprints from appearing on the display.
Sometimes - the presence of a nanocoating, which gives increased smoothness to the surface.
Reliable fastening using silicone elements that prevent the coating from moving and prevent the formation of unevenness and bubbles.

Flexible glass to protect the display of mobile gadgets can also have folded edges. This means that the edges are rounded so the coating is almost invisible. In addition, if the device hits something, the coating will not fall off. So if you are wondering which is the best protective glass, opt for an element with rolled edges.

Removing glass: precautions

Before you get started, there are some rules to consider. First, remember that the glass adheres quite tightly to the display because it is very smooth. But the element is held in place not by glue, but by electrostatic forces. Thus, two perfectly flat surfaces are in close contact, and the glass cannot be removed simply by picking it up with your finger. But you also cannot use a household item, for example, a knife, for this purpose, since there is a risk of damaging the screen or case.

A silicone suction cup will not help in this situation either. If you glue this tool to a damaged coating, a void will form underneath it, and when pressed, it will slide off.

And if the fastening is good, the suction cup will not go anywhere, but another problem will arise. The fact is that the sensor is attached to the body of the gadget using either glue or adhesive tape. The strength of these substances in terms of rupture is much lower than that of glass or touchscreen. Therefore, strong pressure can lead to complete tearing of the display module and damage to its cables. You need to work here carefully and carefully.

How to remove protective glass from iPhone 5S, 4S

Even taking into account the fact that the service life of protective glass is longer than that of films, it also needs to be changed sometimes. The glass comes on a silicone substrate, so it adheres firmly to the display. Removing it will require some skill.

Before removing the protective element, you need to carefully prepare and purchase some tools and materials, namely:

A spatula (or a thin plastic card), a mediator.
Silicone suction cup.
Lint-free cloth.
A glass cleaner that must contain alcohol.
Gloves.

Sometimes it happens that all the tools and materials listed above are included with a new protective glass. But this happens quite rarely.

And the glass removal algorithm itself includes the following steps:

1 You need to wash your hands well with soap before starting work, and then dry them. You don't have to do this, but just wear gloves. This is necessary to prevent fingerprints or streaks from appearing on the display. 2 If the glass is damaged, you need to choose the area that is best preserved and has no chips. You need to attach the suction cup to this place, pressing it tightly. 3 In the corner to which the suction cup is attached, you need to place a pick or a spatula and pry it off. The edge of the coating should peel off. To do this, you will need to pull the suction cup towards you a little, but not too much. To prevent the screen from falling off. This way we will achieve the goal of creating a small distance between the screen and the glass. But if you don’t have a suction cup, just insert the pick deeper. 4 As you peel off the glass, deepen the tool. And if the display is large, you can use 2 mediators or spatulas for the procedure, moving them in different directions. 5 And the last step is to pull the suction cup towards you so that the glass completely moves away from the screen. In this case, you can grab its edges with your fingers and do the same.

How to stick glass on iPhone 6 and other devices

For everything to go perfectly, you need to glue the glass in a clean room where there is no dust. Before sticking the glass, you need to take a lint-free napkin or a simple cloth and slightly wet the display with a cleaning agent or alcohol. This is necessary to clean the surface and remove fatty elements from it.

The gluing procedure is carried out as follows:

1 Pick up a new protective covering for the display. As with removal, keep your hands clean and dry. Or you need to wear gloves. 2 Remove the protective film covering the sticky surface. To do this, you need to grab it by the tongue and pull. 3 How to glue the element itself? The glass should be kept as close to the iPhone display as possible so that small particles of debris or dust do not get on it. After all, any surface tends to quickly accumulate dust. 4 Place the glass cover a few millimeters from the display, align and center it. When gluing, you need to act carefully and carefully ensure that all the holes for the keys, speakers and other elements match. 5 Next, the protective glass on the iPhone 5 is lowered closer to the screen. Lightly pressing and smoothing movements smooth out the surface. So easily we were able to glue the glass to the display. 6 The surface is wiped with a dry cloth. 7 Remove the glued element on top that protected the glass.

If at the end of the procedure you see small dust particles under the protective element, you can peel off part of the glass and blow them out with a vacuum cleaner or remove them with tweezers. Then you need to glue the element back again. You already know how to re-glue glass.

Now you know how to stick a protective glass on an iPhone. There is nothing complicated in this procedure; replacing glass on an iPhone 5S is as easy as shelling pears. Gluing the protective glass on the iPhone requires careful preparation. And the main thing here is to keep everything clean.

Which is better – glass or film?

The answer is obvious - of course, it is better to opt for glass protection. But the point is not only in impact-resistant properties, but also in durability. One has only to note that glass for iPhone 4 or another version of the gadget costs twice as much as regular film.

So the final choice is up to the user. Think for yourself - what is better - to pay more, but in the future avoid expensive device repairs, or save now, but then shell out a lot of money. Screen replacement is one of the most expensive types of repair for Apple gadgets. But, on the other hand, film cannot be called a bad option either.

As a result, the summary will be as follows. The film is affordable. It protects the display from minor scratches, removes glare and covers the entire screen. Is a protective film for the iPhone screen necessary, given its characteristics? Absolutely yes. Moreover, its cost is low, and how to stick the film is an even simpler task than in the case of glass.

Glass is an expensive option. It gives glare, but transmits light to the maximum, and also reliably protects against strong falls and deep cracks. And if you have found a way to save money on an iPhone, you will not be satisfied with cheap protection options. In any case, knowing how to save up for an expensive device, you can find funds for good accessories for the iPhone 6S or other device.