How to fish with a scarf in winter. We make a headscarf, winter version

Fishing in winter is a rather difficult and dangerous task. Prolonged exposure to severe frost can lead to frostbite on your fingers, toes, and facial skin. In addition, fishing on thin ice is very dangerous; many extreme fishermen have already drowned.

And in order to catch perches and roaches in a short time or quickly provide themselves with live bait, fishermen use scarves. What is this catchy tackle and how to use it correctly?

How to make a scarf for fishing

“Televisions and headscarves belong to the so-called screen equipment. They are briefly lowered into the river, then raised and collected fish entangled in the screen net.

“TVs are quadrangular pieces of nets with a sinker and a float, “kerchiefs are triangular. “The scarf is most convenient for winter fishing, when it is easier to pull it into an ice hole.

It’s not difficult to make a fishing scarf yourself. Buy a piece of netting of the required size from a fishing store.

The size of the cells should be selected depending on the type of fish you are going to catch. Prepare a reinforcing rod with a diameter of 3-5 mm; for fishing in the river flow, you may need a rod with a diameter of up to 1 cm.

Spread the mesh fabric on a large surface. Mark the outer cells on both sides with electrical tape or rope (take into account allowances of 2-3 cells per fastener).

Calculate the number of cells in length, mark the middle one. Set aside a distance equal to the height of the scarf.

Count the distance by cells, the lower middle cell should be directly below the top one. Take sharp scissors and cut the edges of the scarf at an angle from the top to the edge cells on both sides.

Each subsequent row should be two cells larger than the previous one, one on each side. You should end up with a triangular canvas with equal sides.

Apply deep notches to the ends of the reinforcing rod with a chisel at a distance of 2 cm (5-6 pcs.). Thread a strong nylon thread into all the cells of the lower edge of the mesh fabric.

Strengthen this thread on the side notches of the reinforcement with reliable knots in such a way that a slight sag of 4-6 cm of the network edge is formed. The thread should run parallel to the reinforcement without forming twists.

Divide the length of the lower edge of the net fabric into four equal parts, mark the cells. Attach the nylon thread in these cells to the reinforcing rod accordingly.

Thread a vein (thick fishing line or nylon rope) upward into the cells of one side of the scarf. Next, pass the same vein down the other side.

Secure the vein to the reinforcing rod where the bottom edge is attached on both sides. The vein should pass through each cell of the mesh fabric up and down.

At the top of the scarf it is necessary to leave 8-10 cm of veins to create a fastening loop. By tightening and stretching the mesh fabric on the side veins of the gusset, you should obtain its required height (0.85 of the total height of the mesh fabric).

This provides a little slack on the sides so that the fish become more tangled in the rig. Tighten the top loop of the gusset fastening with a simple knot.

How to make a scarf for fishing

www.kakprosto.ru

Headscarves are screen tackles. They are lowered into the water for a short time, then rise, after which the fish entangled in the screen net are collected.

TV - pieces of nets of 4-gonal shape, having sinkers and a float. The scarves have a 3-corner shape.

They are mainly used during winter fishing, when it can be easily pulled into the hole. Making such a fishing net yourself is quite easy.

The principle of fishing with a scarf

The scarf is a triangular mesh fabric. A metal wire is mounted at the bottom of the tackle, which serves as a kind of sinker.

The cell size is selected according to the fish that will be caught. For example, to catch small representatives of ichthyofauna, a net with a mesh size of 18-20 mm is used.

The scarf is tied to a rope or thick fishing line and lowered into the hole. To attract prey to the fishing point, you must first lower the bait mixture. Usually the scarf is placed on the bottom, where all types of fish stay in winter.

The most successful fishing is at the beginning of freeze-up, when the fish are actively moving in search of comfortable parking areas.

During the dead of winter, the use of scarves is unpromising, but with the approach of spring, the catchability of this gear increases again.

Sometimes juvenile fish rise to the upper layers of water. In this case, it is necessary to install the mesh product directly under the hole. Fishing with a scarf can be static or dynamic. In the first case, the net is left for a day or overnight, carefully masking the fishing spot.

Some fans prefer to fish in the daytime with regular fishing rods, while simultaneously installing scarves nearby. After 20-30 minutes, the mesh sheets are checked for the presence of prey.

A scarf is a triangular-shaped tackle consisting of a metal frame on which a mesh-shaped canvas is attached. The metal frame also serves as a sinker, which allows the scarf to sink into the water column.

The size of the fabric cells can be different and depends on the purpose of the gear. If you intend to catch small fish (live bait), then the cell sizes can be within the range of up to 20mm, and if you are fishing for full-sized fish (ear or roast), then the cell sizes can be within the range of 50mm or more.

The tackle is attached to a rope and lowered into a hole into which bait was previously poured in order to attract more fish. The scarf sinks to the very bottom, because in winter it is at a depth near the very bottom. The scarf is effective at the beginning of winter and at its end, but at the height of the cold weather, you can hardly catch anything with a scarf.

Depending on the conditions, the tackle can also be installed in the water column, closer to the surface, when the “trifles” rise in search of food or in search of an extra breath of oxygen. Fishing can be either active or passive, when the gear is installed for the night or for the day.

Many fishermen take a scarf with them on regular fishing trips and place it nearby to increase the effectiveness of the fishing itself.

We make a Kerchief, winter version

Making a scarf with your own hands is not very difficult

you can start with a regular, non-folding scarf 180 cm long. It will be catchy and quite easy to make. And transportable.

Making a scarf with your own hands is not very difficult; you can start with a regular, non-folding scarf 180 cm long. It will be catchy and quite easy to make.

And transportable. The scarf consists of a mesh fabric, triangular or trapezoidal in shape, a piece of reinforcement thick depending on the fishing location.

For example, in a crucian pond you can use 3 mm reinforcement or a rigid steel rod, or better yet 5 mm thick reinforcement, so as not to bend it due to inexperience. For currents and small-mesh fishing, you can use reinforcement up to 1 cm thick.

Mesh fabric. Take a mesh fabric 1.8 meters high, let’s assume that you are cutting it from a doll (standard fabric is 60 m long and 1.8 m high) and calculate the number of lower cells for the scarf.

Formula: D/A*0.9 Where D is the length of the reinforcement (mm). For our sample it is equal to 1800, and the cell (mm) (for example, 45, 60, 33, i.e. the mesh of the mesh is the distance of the line between the 2 nearest knots). Usually written on the doll or easily measured with a ruler. 0.9 - landing coefficient.

From the obtained result we take only the whole part, everything after the commas, the fractional part, is discarded. Because this error is taken into account during planting due to the fact that the outermost 4 cm are occupied by fasteners.

This whole part, the number of cells, must be written down on a piece of paper. And write down this amount divided by 4 next to it.

If it is not divided by a whole, let’s say the remainder is 1-3 cells, then distribute it evenly over all quarters when planting. If in some quarter there is 1 cell more, and in another there is 1 less, then the fishing will not be worse, for this a coefficient of 0.9 is taken into account.

Stretch the mesh so that it hangs side by side for several meters. Count the amount of A on the mesh fabric from the bottom corner edge.

Don’t be too lazy to highlight the bottommost cells of your future scarf with some tied wool thread or something else. Otherwise they always distract you or knock you down, then you make a mistake and cut something off at an angle, or you have to recalculate it.

And then you cut it diagonally. From the edge, starting from the second cell from the bottom, cut so that each time the row from the edge is 1 more.

You will get a pyramidal diagonal. So, cut to the top cells and separate the unnecessary corner of the mesh fabric (don’t throw it away, it may be useful for something later).

You should get a pyramidal structure of the edge of the canvas. And the lowest cell is the one you marked; you haven’t reached the other one yet.

Stretch this canvas somehow so that everything is visible.

Making a classic headscarf

The scarf can be used to catch fish of different sizes.

Therefore, the parameters of the gear will have some differences.

The manufacturing technology for such gear is almost the same, despite the fact that it can be used to catch fish of different sizes.

Fishing technique with a scarf

Fishing with a scarf from under the ice is not considered a difficult task. Any beginner can master this method within a few trips to the pond. In this case, most of the time will be spent on searching for fish sites, and not on improving the skills of installing a scarf.

The kerchief is considered a very catchy winter tackle on the first ice and on the last ice. It allows you to catch the required amount of fish at minimal cost.

Fishing scarf

Fishing in winter is memorable for a long time; if you sit at the hole for hours, you can get frostbite on your limbs or fall under the ice. Using a scarf will reduce the waiting time and will help you easily catch live ichthyofauna for dinner.

What is tackle

This is a triangular-shaped screen tackle, the main task of which is to entangle fish in a short time in the water. Thanks to its convenient shape, it is widely used in winter fishing. It consists of a frame made of metal and a mesh mesh attached to it, and the size of the cells depends on the size of the fish that is caught with this tackle. The weight of the frame serves as a sinker in the water.

After feeding, the tackle is attached to a rope and immersed in the hole. The success of fishing with a scarf depends on the fishing conditions: the active peak of the bite will be at the beginning and end of winter, in severe frost it will be difficult to catch anything with it.

A scarf is a very useful piece of equipment for every fisherman. Let’s look at what is required for manufacturing, and how to make a scarf for fishing with your own hands will be described in the next section:

fishing net - the size of the mesh depends on the fisherman, the choice is individual;
5 mm wire - it is necessary to create a frame;
nylon thread, thick fishing line.

Use scarves at the very beginning of winter, when the ice has just hardened. Fishing at this time is much more effective, since during this period they are looking for a place to stop, but be careful - fishing on thin ice can be dangerous.

Manufacturing

Making a scarf for fishing according to the correct pattern is very simple; using this simple pattern, you can make several scarves and actively use them while fishing.

Find a comfortable room to start working on, a flat surface, after which we begin to answer the question - how to make a headscarf for fishing:

The prepared mesh must be placed on the floor or other flat surface, and then the workpiece must be cut off. A mark is made on the frame at intervals of 2 cm for more accurate installation of the mesh.
A fishing line is threaded through the bottom of the workpiece, after which it must be tied in the places where the marks were made.
A nylon thread is attached to the mesh and the wires located on the sides; to create a reinforced layer, it is necessary to thread the thread through each cell of the mesh. Make loops there to install a rope in them, by which they will immerse the scarf in the water.

For a quick dive, pay attention to the sinkers.

Before answering the question of how to make a scarf for fishing, let's consider several informative points describing this gear and in what area it will be more effective. It is best to use a scarf for winter fishing. Fishing in winter is memorable for a long time; if you sit at the hole for hours, you can get frostbite on your limbs or fall under the ice. Using a scarf will reduce the waiting time and will help you easily catch live ichthyofauna for dinner.

Fishing tackle "kerchief" is widely used in winter fishing because of its convenient triangular shape, which easily fits into the hole. Before you start fishing, the fishing area is well-fed, and only then do they begin to install the gear. After feeding, the tackle is attached to a rope and immersed in the hole. The success of fishing with a scarf depends on the fishing conditions: the active peak of the bite will be at the beginning and end of winter, in severe frost it will be difficult to catch anything with it.

A scarf is a very useful tackle for every fisherman.

Let's consider what is required for manufacturing, and how to make a scarf for fishing with your own hands will be described in the next section:

fishing net - the size of the mesh depends on the fisherman, the choice is individual;
5 mm wire - it is necessary to create a frame;
nylon thread, thick fishing line.

Use scarves at the very beginning of winter, when the ice has just hardened. Fishing at this time is much more effective, since during this period they are looking for a place to stop, but be careful - fishing on thin ice can be dangerous.

Making a scarf for fishing according to the correct pattern is very simple; using this simple pattern, you can make several scarves and actively use them while fishing.

Find a comfortable room to start working on, a flat surface, after which we begin to answer the question - how to make a headscarf for fishing:

The prepared mesh must be placed on the floor or other flat surface, and then the workpiece must be cut off. A mark is made on the frame at intervals of 2 cm for more accurate installation of the mesh.
A fishing line is threaded through the bottom of the workpiece, after which it must be tied in the places where the marks were made.
A nylon thread is attached to the mesh and the wires located on the sides; to create a reinforced layer, it is necessary to thread the thread through each cell of the mesh. Make loops there to install a rope in them, by which they will immerse the scarf in the water.

For a quick dive, pay attention to the sinkers.

Feeding and catching

There should be no difficulties in making it, and in the process of fishing too, the main problem of fishing with a scarf is finding fish sites, the right feeding and time. Any ready-made mixtures, plant and animal additives - such as crackers, steamed grains, cake and maggots - are suitable as a fishing mixture for complementary feeding.

Step-by-step process of fishing with a scarf:

To successfully start fishing with scarves, you need to drill a hole, for this we purchase an ice ax;
Having drilled a hole, we feed the fish - you need to use special feeders that can be immersed to the very bottom, after which the container opens and the mixture remains at the bottom;
Now we lower the tackle into the hole, the sinker with the lower part should lie on the bottom, and the net should be stretched like a canvas, the cord is tied to a stick. Now we calmly fish with a scarf, sitting in a warm place and waiting for the catch.

“I fish at night, before leaving the scarf, I cover the hole with snow and branches: the snow prevents the hole and scarf from freezing, and also camouflages the tackle, the fish behaves calmer and the next morning I check the tackle and collect the catch, almost always a good one is caught perch” - according to an experienced fisherman.

Having figured out the question of how to fish with this tackle, you can safely go winter fishing - the catch will be big.

But don’t be greedy, take fish in moderation for dinner. Take care of yourself and nature while on the ice.

True fishing fans, with a steely character and iron patience, do not go on vacation even in winter. And although the warm autumn gives way to unbearable frosts, instead of a light breeze a strong blizzard blows and snow blows, fishermen continue to successfully get decent trophies from fresh holes. For such purposes, they use different gear, including a fishing scarf.

It's no secret that fishing in winter is a rather risky and demanding activity, especially if it is carried out in extreme weather conditions. Wrong approach and lack of responsibility- a direct path to serious consequences. In addition to frostbite on your fingers, you can become a victim of a much more dangerous problem in the form of ice damage and death in icy water.

But despite the dangers, the weak activity of the inhabitants of the depths and a host of other pitfalls, fishing masters confidently continue to do what they love. And fishing with scarves in winter is one of the most exciting ways to catch good prey even under the most unfavorable conditions.

The tackle is a specific triangular design, which consists of a metal base with a mesh-shaped canvas. The first component plays the role of a sinker, plunging the scarf into the water column. In this case, the size of the fabric cells varies and is determined by the amount of expected production. If you are going to catch small representatives of the aquatic world, for example, live bait for girders, then the optimal diameter of the cells can vary within 20 mm. When searching for full-size trophies for fish soup, this figure is increased to 50 mm or more.

The tackle is fixed with a rope to some object on the surface, after which it is immersed in a pre-fed hole. The canvas is located directly on the bottom, because in winter you should look for fish there. Fishing with a scarf shows particular effectiveness in the first days of winter, but during the deep winter it is practically useless.

Taking into account the fishing conditions, the tackle is also fixed in the water column, closer to the upper horizon, if the “trifle” rises there in search of food and available air. At the same time, fishing itself can be either active or passive, implying the installation of a headscarf for the night or for the day. By the way, some fishermen take such a device with them on regular fishing trips, installing it near other gear.

Many beginners are interested in how to make a scarf for winter fishing, completely abandoning the purchase of store-bought models. In fact, it is not difficult to make such a fishing tool with your own hands, and its functionality will be much wider than that of a purchased version. To successfully complete the task, just follow the step-by-step guide, taking into account some important aspects:

Making a homemade headscarf is not at all difficult, provided that you follow the key details. You can start with a regular non-folding tackle 1.8 meters long. This option demonstrates good catchability with compact size and good transportability.

The product is based on a mesh fabric, preferably triangular or trapezoidal in shape, a piece of reinforcement with optimal thickness. It is chosen taking into account the fishing conditions, because, for example, in a crucian pond, 3-mm reinforcement or a steel rod are effective, and when fishing in the current, there is nothing better than reinforcement 1 cm thick).

As a canvas, you need to take any fishing net with a height of 180 cm, correctly calculating the number of lower cells.

Fishing with a scarf- this is a very exciting activity that interests not only experienced fishing masters, but also beginners who want to experience new emotions and get vivid impressions. Fishing with this method is very simple, so even an inexperienced person can easily master the basic subtleties of casting techniques and further operation of the gear. The key to successful fishing is determining the current location of the fish. To do this, you need to at least understand the peculiarities of its behavior in winter, taking into account the many years of experience of colleagues and local fishermen.

It is no secret that in the first days of winter, the inhabitants of the depths stay in wintering pits almost without leaving them. To quickly determine their location and then go fishing successfully, you should follow these recommendations:

Considering all of the above, we can confidently say that fishing with a scarf- a very simple, interesting and productive activity. But in order for the result to meet expectations, it is important to adhere to the listed rules.

Do not forget that the behavior of the inhabitants of the depths in different bodies of water can be the most unpredictable. And this applies not only to food preferences, but also to the choice of habitats, reaction to individual baits, as well as other points.

To ensure that going out to the pond does not turn out to be a waste of time, follow these rules:

The time was about 10 o'clock in the morning. I woke up early and didn’t want to fall asleep again. After lying there for about half an hour, an interesting thought occurred to me. And she came to me because from the window of my house I can see the roof of my neighbors. A cat was walking along this roof, carrying some food in its teeth. Whether it was a fish or a piece of meat remained unknown to me. However, it was thoughts about fishing in winter that began to arise in my head. After 15 minutes of thought, I came to the conclusion that it would be nice to catch fish without much time investment. Namely, use a scarf as the main fishing tool. In case anyone has forgotten, a scarf is a triangular-shaped net. A piece of wire up to 1.5 meters long is used as a load, and a foam float is tied on top. This is the gear I decided to use to fish. The technique of installing a scarf in winter has long been known to me. A couple of years ago I already had experience installing nets on ice, and at the same time I installed several gussets. Unfortunately, I don’t remember the result of the last fishing, so I decided to experiment and hope for the best. With these thoughts in mind, I already put on the kettle and warmed up some porridge for myself. The entire process of eating food was accompanied by brain activity. By finishing the last cookie, I already knew exactly what and how I would do in the next hour.
The day turned out to be surprisingly cold. I didn’t have time to look up the weather on the Internet, and I don’t have a regular thermometer. Putting on sports tights and a light jacket, I went to the garage. Going out into the yard, I realized that I had dressed very lightly, but returning was a bad omen. Fortunately, the garage is located 10 meters from the entrance to the house. I live in the private sector. Therefore, I did not manage to freeze pretty much, although the weather was conducive to this. Having quickly found my bearings in the garage, I took out several metal rods with scaffolding and ropes wound around them. These were scarves. I had them because as a child I was fond of knitting these same scarves. Having dragged all this dirt into the house, I began to prepare for the upcoming trip to the ice.
The essence of the invented method was as follows. Having drilled a hole, she is fed with an abundance of food. After lowering the fertilizer, a scarf is placed. Everything is simple and not tedious. The good catchability of this method would mean that you would no longer have to sit with a fishing rod waiting for a bite. I installed a few scarves and you can go home. The catch was planned to be collected the next day. However, an option would also be suitable, in which fishing is also done with a fishing rod, and scarves are like a safety net and confidence in the availability of the catch.

As an experiment, I decided to use a small mesh scarf. The cell size was 18 mm. Those who understand these meanings now grinned. The fact is that this is a very small mesh, and you can only catch live bait in such a scarf. However, it was not the big catch that drove the process, but my curiosity. The gusset was checked for holes and equipped with an additional piece of scaffolding. When fishing in summer, the scarf is simply thrown into the water with a stick. You can also lower it from the boat. In winter, you need to lower the scarf into a narrow hole from under the ice screw. That's why an additional piece of fishing line was required, attached to one of the ends of the weight wire. Having secured one end, I measured a couple of meters and tied the other end of the line to the main rope. Now the scarf can be lowered into the hole, holding it by an additional piece, and after it is in the water column, I will take the main rope, and the scarf itself will take the correct shape in the water.
The scarf was ready for fishing. Meanwhile, in the kitchen, water was boiling in a saucepan. I was cooking porridge. Or rather, I cooked several types of cereals. It was semolina, peas, pearl barley. A little bit of everything, but in the end it turned out to be half a plastic bag. I mixed all the porridges together, and also added soaked bread. Having put the mass in a plastic container, I went to get dressed.
By that time I had already checked the weather. -28 degrees. For many anglers, this temperature is unacceptable. But I, charged with optimism and enthusiasm, could not retreat. Felt boots, a warm jacket, three pants, three socks, a hat, a down jacket and mittens - that's what I was wearing that day. I left the house.
It would seem that everything is ready and you can move forward. But I did not find the ice screw in its usual place. Then I remembered that in the fall I used to dig holes for fence posts with them. At this point, experienced fishermen will smile again. Because the ice drill, after interacting with the ground, could hardly drill through the ice with confidence. I wouldn't say I didn't try to do something. Taking a file, I worked magic on the dull knives. In the end, this turned out to be, of course, not enough, but first things first.
I forgot to say that I am satisfied with winter fishing, interesting and traditional. That is, even with a fishing rod, sitting in a warm tent, I fish with interest and pleasure. But experiments and an unconventional approach are a characteristic feature of me. That’s why I’m already approaching the frozen and snow-covered river.
I considered experimenting on the river itself unnecessary and ineffective. It's all about the flow. And the bait, which was supposed to be the key factor, would be carried downstream, thereby distracting the fish from the installed net. I headed to the backwater, so to speak. It’s very good that we have a place nearby where the current has no power over the water. This backwater has connections with the river, but overall it looks like a separate lake. This is where you can find an abundance of fishermen. For reference, I will say that on weekends you can see up to 30 tents with fishermen on the ice. In principle, fish are caught and many people prefer to sit on the ice instead of lying on the sofa.
So I arrived at the place. The frost has pretty much crippled the ranks of winter fishing enthusiasts. In addition, it was already evening, about 4 o’clock. A couple of tents were visible in the distance, and there wasn’t a soul near me.
Having looked around the area, I found a suitable bend near the shore, opposite which, as it seemed to me, there should probably be a fish. This was supported by the fact that there were several wooden sticks, which means that pike were caught here. If there is pike, then there is small fish, I thought. I started drilling a hole exactly between two tent sites. Apparently, fishermen were sitting on them in the morning, and now I had the opportunity to catch the fish they fed. This is where the first incident happened. The ice drill didn't want to drill into the ice. With great difficulty and noise, I drilled only 15 centimeters, and that was because I put a lot of pressure on the ice drill with my weight. Realizing that this attempt would not be successful, I went to study the age of the tent sites. And lo and behold, they were indeed fresh. A few manipulations with the ice auger along the old hole, and I saw water. Sighing with relief, I took out the shabala and pulled out the ice from the hole. Having perked up, I was already scooping up the bait I had prepared at home. And I scooped it into the feeder. It’s worth telling a little about this tool. A homemade feeder designed for targeted delivery of food to the bottom. It is designed in such a way that with a slight movement of the hand, its bottom opens, and all the bait spills out in close proximity to the bottom. I lowered about 3 feeders to the bottom. The capacity of one is a good handful of food. In addition to the bottom, I decided to open the feeder half a meter, and also a couple of times a meter from the bottom. Well, I threw a few handfuls of the remaining food into the hole itself. The remains of the porridge slowly swirled in the lenka, and I circled around it, warming my already freezing legs and arms. – 28 in an open area, and even with the wind it turned into – 30. Literally after 3 minutes, I felt fine and untwisted the tackle with my bare hands. The process of lowering the “fresh” scarf did not cause any trouble. I placed it at the very bottom, slightly pulling the main rope, and giving the scarf a “tight” position. After holding the rope with his finger and making sure that no fish immediately fell into the net, he went for a walk along the lake. Standing still was a bad idea, because, as you know, blood that is not actively circulating in the limbs quickly gets cold. Having made a small circle, which took about 20 minutes of my time, I returned to my gear. He pulled it out and was surprised. There was not a single fish in the scarf. Having thought about it as much as the situation allowed, I decided to place it again, but this time at a distance from the bottom. The fact is that I remembered how last year we caught fry on the first ice. Then the fish could be seen directly from the hole. Small baitfish swam right under the ice. Deciding that maybe now the fish was in the shallow end of the water, I raised the scarf a couple of meters above the bottom level. Another 20 minute walk, again I am standing at the hole. Pulled it out - empty. It was not possible to experiment with the place, again because of the auger, and I began to get ready.
On the way home, I made conclusions and assumptions. Everything concerned without an effective experiment. The main question: “Why?*” I found several answers in my head: Wrong fishing spot. The scarf didn't last long.
It is, of course, impossible to draw exact conclusions, and therefore I set myself up for further experiments. I decided that the first thing I needed to do was buy new knives for the ice auger. Equip a couple more scarves and place them in different parts of the reservoir. I also thought about experimenting with food. Maybe it would be worth using flavorings and live additives - bloodworms or hunchbacks. After all, in winter the fish are not so active, and perhaps in such frost they are not tempted to eat simple porridge.
I was home already at dusk, pretty frozen and surprised by the result of the fishing. But nothing can be done, you need to accept this as a given of today’s experiment and try something else. This was my experience. I wish you a good bite, warm weather, and the realization of your thoughts!